Can I Set Up A Bathtub Myself?
Can I Set Up A Bathtub Myself?
Blog Article
They are making a few good annotation about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround in general in this post below.
Setting up a bath tub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and also in some cases, tiling skills. Replacing an old tub with a brand-new one is also a reasonably difficult job. If the old bathtub is conveniently accessible, the project can move immediately; if you need to open a wall to get rid of the old bathtub and also position the new tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly need a helper to leave the old tub as well as embeded in the brand-new one. Ensure you have actually certified on your own for the work and are comfortable attempting it. Rather than employing a specialist to take control of a halfway-completed task, it is better to consider employing one before you begin. Possibilities are you might require a specialist plumber to make tube links.
This write-up will aid you mount a brand-new bathtub in your bathroom if you have actually already acquired a new bathtub and don't require to transform the arrangement of your previous water supply pipes.
Your tools and material checklist ought to comprise the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is separate the water. After doing so, activate the taps to drain any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be fairly bothersome as a result of the limited access that is frequently the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will come from the pipes. As soon as the supply pipelines have been removed, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any old securing compound.
Prior to going on to fit the brand-new taps, contrast the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, then you will require minimizing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin ensuring that the washers remain in place in between the tap and also the sink. Secure the faucet in place with the maker offered backnut. When the tap is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular faucet connectors. The previous kind ought to be linked to the faucet ends initially, tightening only by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are valuable in equally spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny points.
The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bath tub until the spirit level reviews degree.
To install taps, fit all-time low of the outermost flexible tap adapter to the appropriate supply pipe by making a compression join; after that do the very same for the various other tap.
Turn on the water system and also examine all joints and new pipework for leaks as well as tighten them if needed. Load the bath tub and also inspect the overflow electrical outlet as well as the typical electrical outlet for leakages.
Ultimately, fix the bath paneling as explained in the maker's user's manual. Tiling and also sealing around the bathtub ought to wait until the tub has been utilized at the very least when as this will certainly resolve it right into its last position.
Preparing for the Installment
Firstly, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is necessary to make sure that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to stop pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to now be ready to be suited its final position.
Tiling Around the Bathtub
In the location where the bath satisfies the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to split a rigid seal, creating the water to permeate the wall surface between the bathroom and the tiling, causing problems with dampness and also possible leakages to the ceiling listed below.
You can choose from a range of coloured sealants to assimilate your fixtures and also fittings. They are sold in tubes as well as cartridges, and can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to always fill the bath tub with water before sealing, to permit the movement experienced when the tub remains in use. The sealant can fracture fairly very early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily readily available on the market. It is a good idea to fit the tiles utilizing waterproof or waterproof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very interested in How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I hope you enjoyed our article. Sharing is caring. Helping others is fun. We take joy in reading our article about Installing A Bathtub.
Phone
Report this page